Degreasers/Cleaners
Lubrication solutions
Degreasers/Cleaners
VOC-free degreasing agent
MOLYDAL EMULSIFIABLE CLEANING AND DEGREASING FLUID THAT REMOVES BITUMEN AND TAR KL BIO
Eco-friendly lubricants
EMULSIFIABLE CLEANING AND DEGREASING FLUID THAT REMOVES BITUMEN AND TAR
Bitumen and tar removal cleaning and degreasing agent
An emulsifiable degreasing agent developed to replace petroleum-based solvents.
KL BIO can be used undiluted and rinsed off with water.
VOC-free and biodegradable No listed carcinogenic, mutagenic, toxic, reprotoxic or noxious substances. (Order of 9 November 2004) KL BIO can be recycled with heat. An anti-corrosion coating remains after cleaning.
VOC-free degreasing agent
• A powerful degreasing agent• KL BIO is an emulsifiable degreasing agent developed to replace petroleum-based solvents.
• KL BIO can be used neat and rinsed with water.
• KL BIO may also be used with water (from 3 to 50%) according to the nature of the soiling to be cleaned
• KL BIO may be recycled at ambient temperature.
• After cleaning, a protective film against corrosion is left.
• The low rate of evaporation of KL BIO reduces its consumption considerably
• Nature: Methyl ester
• Aspect: Limpid
• Color: Color free
• Smell: very low
• Volumetric mass to 25°C: NF EN ISO 12185 0.89 kg/m3
• Flash point in isolation NF EN ISO 3104 >150 °C
• V.O.C. content : 0
• Evaporation Index (ether =1) DIN 53170 > 1000
Aerosol: Every positions, even upside down.
Propeller without V.O.C
KL BIO is applied with a cloth, poured or sprayed or the object immersed in it.
KL BIO can be used on a cloth, in a degreasing fountain (fitted with diaphragm pumps), by sprinkling, or by immersion.
It can also be used with water (3 to 50%) depending on the nature of the dirt to be removed.
Aerosol: Multi-position spraying.
DN1 SURFACE CLEANER
The DN1 is a powerful surface cleaner and degreaser of the KRISTAL brand. It must be used before every impression to eliminate oils and greases on the surface.
It evaporates quickly, leaving a clean and residue-free surface.
It evaporates quickly, leaving a clean and residue-free surface.
Designation: DN1 Surface Cleaner
Volume : 400 ml
Type : Spray
Color : Colorless
Odour : Characteristic
Boiling point : -78°C
Flash point : -26°C
Ignition temperature : 200°C
Density at 20°C: 0,64 g/cm³
Cleaning and Degreasing
MOLYDAL WORKSHOP DEGREASING AEROSOL STARNET
A cold degreasing agent with very strong solvent properties. Grease, oil and sludge removal; it also removes labels (it may attack rubber and plastics).
Perfectly suitable for degreasing operations on all metals where quick evaporation is required.
The STARNET grease remover is guaranteed not to contain chlorinated solvents, HCFCs or glycol ether.
STARNET is a non-greasy cold degreaser with very high solvent power.
STARNET is perfectly suitable for all degreasing operations on all kinds of mechanical parts where a fast evaporation rate is desired. On account of its very high solvent power, STARNET eliminates very easily greases, oils, dirty oils or greases, inks, temporary oil and wax protections.
STARNET is inert with respect to rubbers and most plastics. However, compatibility can vary with the application’s conditions. Therefore, it is recommended to verify before using.
STARNET contains less than 200 PPM in sulfur and halogens (chlorine and fluorine) ; therefore, it responds to the P.M.U.C..nuclear specifications.
Aspect : Liquid
Color : Colorless
Smell : Slight
Density at 20° C : NFT 30-020 : 0.85
D.P.O. 0
Flash point : ISO 2719 < 0° C
Index K.B : 165
Freezing point : ASTM D86 < -50° C
Water solubility : Insoluble
Packaging : 650 ml
USES:
For degreasing operations on all metals where quick evaporation is required.
Cleaning and rinsing agent for all electrical or electronic mechanisms turned off, such as hi fi or telephony equipment; windings ; relays ; printed circuits ; radar gear ; counters, and so on.
Usable before gluing of plastic or metal parts.
Elimination of greases, oils, dirty oils and greases, and other chemical products.
Cleaning and degreasing of all mechanical parts (chains, bearings, pinion gears, filters, brake drums, etc.). Cleaning of paper making cylinders.
Elimination of print shop inks.
Cleaning of injection nozzles and mould prints.
Ungluing of labels.
KL 50 AL FOOD QUALITY DEGREASING AGENT HIGH SOLVENT POWER
KL50 AL cleans and degreases all mechanical parts (chains, lines, bearings, pinions, filters, etc.) without leaving residue after evaporation. KL 50 AL is specially formulated for spray application, notably because of its low odour. Non-Food Compounds Program Listed K1 Registration: 142221.
The KL 50 AL is guaranteed free of chlorinated solvents, HCFCs or glycol ether.
The KL 50 AL has been specially formulated for its spraying usage because of its very slight smell.
The KL 50 AL cleans and degreases all kinds of mechanical parts (chains, bearings, pinions, filters...) without leaving residues after evaporation.
On account of its very high solvent power, the KL 50 AL eliminates very easily greases, oils, dirty oils or greases, inks, temporary oil and wax protections.
The KL 50 AL is inert with respect to rubbers and most plastics. However, compatibility can vary with the application’s conditions. Therefore, it is recommended to verify before using.
The components of KL 50 AL are certified by the National Sanitation Foundation (NSF), which is based on the Food and Drug Administration’s (FDA) class H1 requirements.
This indicates that it is authorized to be used during an incidental contact with food.
Aspect: Liquid
Color : Colorless
Smell : Slight smell of solvent
Density at 20° C : NFT 30-020 : 0.76
D.P.O. 0
Flash point : ISO 2719 > 24° C
Index K.B : 33
Freezing point : ASTM D86 < -20° C
Vapor tension at 20°C : 5 hPa
Surface tension at 25°C: 23.7 mN/m
Evaporation / (ether = 1) ratio DIN 53170 25
Can be use on hot molding parts
Cleaning and rinsing agent for all electrical or electronic mechanisms turned off, such as Hi Fi or telephony equipment ; windings ; relays ; printed circuits ; radar gear ; counters, and so on.Usable before gluing for plastic or metal parts.
Elimination of greases, oils, dirty oils and greases, and other chemical products.
Cleaning and degreasing of all mechanical parts (chains, bearings, pinion gears, filters, brake drums, etc.).Remove the labels.